Lead screw limiters for motor - RF Cafe Forums

The original RF Cafe Forums were shut down in late 2012 due to maintenance issues - primarily having to spend time purging garbage posts from the board. At some point I might start the RF Cafe Forums again if the phpBB software gets better at filtering spam.

Below are the old forum threads, including responses to the original posts.

-- Amateur Radio
-- Anecdotes, Gripes & Humor
-- Antennas
-- CAE, CAD, & Software
-- Circuits & Components
-- Employment & Interviews

-- Miscellany
-- Swap Shop
-- Systems
-- Test & Measurement
-- Webmaster

troy

Post subject: Lead screw limiters for motor

Posted: Mon Feb 25, 2008 4:57 pm

Captain

Joined: Mon Feb 25, 2008 4:53 pm
Posts: 10

Hey guys

I'm using a car window motor to drive a lead screw with the standard automotive 12V system. Is there a simple way to put something inline so when the leadscrew reaches the end of the travel and hits a stop, it stops the current to the motor. the stock unit must have something built in but I need different limits. Im trying to avoid mechanical limit switches.

Troy :smt017

nubbage

Post subject:

Posted: Tue Feb 26, 2008 5:19 am

General

Joined: Fri Feb 17, 2006 12:07 pm
Posts: 304
Location: London UK

Hi Troy
If you are against mechanical limit switches because of dust, then you might consider a ceramic magnet on the traverse driven by the lead screw , which operates a reed relay at the limiting points.

troy

Post subject:

Posted: Tue Feb 26, 2008 11:27 pm

Captain

Joined: Mon Feb 25, 2008 4:53 pm
Posts: 10

Thanks Mr. Nubbage

I am using this to open and close a vent in a shop so you're right that I am worried about dust and other crap in the air (including bugs). I need to open the unit and see where the existing limit switches connect into the circuit. So do you have a manufacturer to suggest for your kind of limit switch, or should I just do an Internet search for something? I'm guessing the current level that the switch needs to carry is pretty low so just about anything will work?

Thanks.

nubbage

Post subject:

Posted: Wed Feb 27, 2008 7:44 am

General

Joined: Fri Feb 17, 2006 12:07 pm
Posts: 304
Location: London UK

Hi Troy
The beauty of the approach is that the components are readily available and very tolerant of environment.
Just google for "ceramic magnets" and "reed relays", and that should throw up a number of local sources in your area. When you have a handfull (and they are inexpensive) just fiddle around with different arrangements on a test fixture until you get reliable switching every time.
Reed relay contact ratings go up to several amps, and the sensing distance for the ceramic magnet is several millimetres, so tolerances are relaxed whilst still ensuring reliable operation. Ceramic magnets, as you might guess, are high-energy types and can operate up to quite high ambient temperatures without demagnetizing.
Give us some feedback how the project is going later.

Posted 11/12/2012

Webmaster:

Kirt Blattenberger,

BSEE - KB3UON

RF Cafe began life in 1996 as "RF Tools" in an AOL screen name web space totaling 2 MB. Its primary purpose was to provide me with ready access to commonly needed formulas and reference material while performing my work as an RF system and circuit design engineer. The World Wide Web (Internet) was largely an unknown entity at the time and bandwidth was a scarce commodity. Dial-up modems blazed along at 14.4 kbps while tying up your telephone line, and a nice lady's voice announced "You've Got Mail" when a new message arrived...

All trademarks, copyrights, patents, and other rights of ownership to images and text used on the RF Cafe website are hereby acknowledged.

My Hobby Website: AirplanesAndRockets.com

My Daughter's Website: EquineKingdom