Visit RFCafe.com Thanks for visiting RFCafe.net Thanks for visiting the RF Cafe Archives Thank you for visiting RF Cafe Thank you for visiting the RF Cafe Archives!

Antenna parameters - RF Cafe Forums

The original RF Cafe Forums were shut down in late 2012 due to maintenance issues - primarily having to spend time purging garbage posts from the board. At some point I might start the RF Cafe Forums again if the phpBB software gets better at filtering spam.

Below are the old forum threads, including responses to the original posts.

-- Amateur Radio
-- Anecdotes, Gripes & Humor
-- Antennas
-- CAE, CAD, & Software
-- Circuits & Components
-- Employment & Interviews
-- Miscellany
-- Swap Shop
-- Systems
-- Test & Measurement
-- Webmaster

sandra
 Post subject: Antenna parameters
Posted: Sat Jul 11, 2009 7:12 pm 
 
Lieutenant

Joined: Sat Jul 11, 2009 6:57 pm
Posts: 1
Hi I am new to satellite field, could any body help me to explain in simple terms what is

a. polarization
b. cross polarization discrimination
c. cross polarization isolation

S Larsen


 
   
 
nubbage
 Post subject: Re: Antenna parameters
Posted: Mon Jul 13, 2009 4:03 am 
 
General
User avatar

Joined: Fri Feb 17, 2006 12:07 pm
Posts: 236
Location: London UK
Hi Sandra
I don't have a classical textbook with me, but without here goes:
a) Polarization: every real antenna establishes E and H vectors around it when the energy in the feeder reaches the antenna structure. Conventionally, we think of the E field, because the H field is directly related to it, but 90 degrrees apart in space. Due to the way the current flows on the surface of the conductive elements making up the antenna, most of the E field will be oriented in one vector direction relative to a fixed set of orthogonal co-ordinates, on earth taken to be the horizon. If the direction is parallel to the earth's horizon, conventionally we define this as horizontal polarization, and of course if vertical to the horizon, vertical polarization. If current can be pursuaded by design of the structure to follow a particular curved path, then circular polarization results, and this is right hand or left hand depending on which sense the curved path follows.
b) and c) In the desciption above, I deliberately said "most of the E field", because the flow of current will establish E field in both the hozizontal plane and the vertical plane simultaneously. The ratio of these two vector magnitudes in dB is the cross-polarization level. In a circular polarized antenna with perfect circularity, this will be zero dB, because the E field level that can be measured is the same in the horizontal as well as the vertical plane. If you imagine a fat dipole, however, with the elements horizontal, most of the E field vector will be horizontal. However, some current will flow across the cylinder, around the curved direction, and thus it will set up a vertical E field. Let us assume this level is -15dB compared to the horizontal level. If an ideal horizontally polarized antenna were to be used as a far field source, with no vertical polarization, the level of energy received in the fat dipole is taken as 0dB when they are both in the same plane. If now the perfect antenna is rotated to the vertical, the level received should fall to zero, but will actually fall to -15dB. This is the cross polar discrimination. In my book, it is also the cross-polar isolation, but purists might disagree and argue the point.
Essentially, cross polar discrimination shows the ability of an antenna to separate, in the above example by rotating it, or discriminate, the pure vertical from the pure horizontal polarization of a received signal.

_________________
At bottom, life is all about
Sucking in and blowing out.




Posted  11/12/2012
RF Stencils for Visio v3.1 by RF Cafe
RF Cascade Workbook 2018 (GS) - RF Cafe
About RF Cafe Archives
Kirt Blattenberger - RF Cafe Webmaster
Copyright: 1996 - 2024
Webmaster:
    Kirt Blattenberger,
    BSEE - KB3UON

RF Cafe began life in 1996 as "RF Tools" in an AOL screen name web space totaling 2 MB. Its primary purpose was to provide me with ready access to commonly needed formulas and reference material while performing my work as an RF system and circuit design engineer. The Internet was still largely an unknown entity at the time and not much was available in the form of WYSIWYG ...

All trademarks, copyrights, patents, and other rights of ownership to images and text used on the RF Cafe website are hereby acknowledged.

My Hobby Website:  AirplanesAndRockets.com

spacer