Visit RFCafe.com Thanks for visiting RFCafe.net Thanks for visiting the RF Cafe Archives Thank you for visiting RF Cafe Thank you for visiting the RF Cafe Archives!

Rectangular patch antenna design - RF Cafe Forums

The original RF Cafe Forums were shut down in late 2012 due to maintenance issues - primarily having to spend time purging garbage posts from the board. At some point I might start the RF Cafe Forums again if the phpBB software gets better at filtering spam.

Below are the old forum threads, including responses to the original posts.

-- Amateur Radio
-- Anecdotes, Gripes & Humor
-- Antennas
-- CAE, CAD, & Software
-- Circuits & Components
-- Employment & Interviews
-- Miscellany
-- Swap Shop
-- Systems
-- Test & Measurement
-- Webmaster

jrk
 Post subject: Rectangular patch antenna design
Posted: Mon Jan 22, 2007 6:44 am 
 
Lieutenant

Joined: Mon Jan 22, 2007 6:08 am
Posts: 2
Hi,

I'm in the process of designing a simple microstrip rectangular patch antenna. I intend to feed the structure by using a co-axial wire inserted through a hole in the ground plane, and substrate. I understand that the (0,1) and (0,3) modes of a rectangular patch resonator both exhibit broadside radiation and the same polarization. But what exactly is meant by (0,1) etc.? Also I presume that one can only excite these two modes if the antenna is dimensioned correctly and fed in the correct location. Could anyone elaborate on what is required?

I have found a formula than can be used to determine dimension L. But didn’t find such formula for W. I understand that W must be less than a wavelength in the substrate material, in order to avoid the excitation of higher order modes. Aside from this limitation can/should one dimension W arbitrarily? Several of the rectangular patches in the literature seem to have a L/W ratio of about 0.75, is there a reason for that?

Thanks

_________________
James


 
   
 
jrk
 Post subject: A tutorial answering my questions
Posted: Thu Jan 25, 2007 4:19 am 
 
Lieutenant

Joined: Mon Jan 22, 2007 6:08 am
Posts: 2
For anyone who’s interested in this I found answers to my questions in a really well written tutorial on the RF globalnet site.

Title: The Basics Of Patch Antennas
By: Orban Microwave Products

Thanks,
James

_________________
James


 
   
 
nubbage
 Post subject:
Posted: Fri Jan 26, 2007 1:12 pm 
 
General
User avatar

Joined: Fri Feb 17, 2006 12:07 pm
Posts: 218
Location: London UK
Hi jrk
Thanks for that.
I tried to put a reply together based on articles I have culled from various tech pubs, but the guys writing the papers just wanted to goof off sprinkling bessel integrals all over the place, which wasn't much use to answer your very apposite question.

I have often needed design curves for various patches such as dual frequency, various bandwidths etc but never could find a straight forward kitchen sink treatment.

Thanks again






Posted  11/12/2012
RF Stencils for Visio v3.1 by RF Cafe
RF Cascade Workbook 2018 (GS) - RF Cafe
About RF Cafe Archives
Kirt Blattenberger - RF Cafe Webmaster
Copyright: 1996 - 2024
Webmaster:
    Kirt Blattenberger,
    BSEE - KB3UON

RF Cafe began life in 1996 as "RF Tools" in an AOL screen name web space totaling 2 MB. Its primary purpose was to provide me with ready access to commonly needed formulas and reference material while performing my work as an RF system and circuit design engineer. The Internet was still largely an unknown entity at the time and not much was available in the form of WYSIWYG ...

All trademarks, copyrights, patents, and other rights of ownership to images and text used on the RF Cafe website are hereby acknowledged.

My Hobby Website:  AirplanesAndRockets.com

spacer